XYZprinting Da Vinci 2.0

7 reviews

Dec, 2024

Positive
price (10)
usability (6)
print quality (2)
performance (2)
design (1)

Negative
reliability (4)
size (3)
durability (1)

General overview
Price comparison

alaTest has collected and analyzed 7 reviews of XYZprinting Da Vinci 2.0. The average rating for this product is 3.2/5, compared to an average rating of 4.0/5 for other products in the same category for all reviews. People really like the print quality and performance, but opinions about the design and usability are different. Many are critical about the durability and size.

price, performance, print quality

reliability, size, durability

On average, users rate this product 63/100.

Review analysis

(Based on 7 reviews)

User Reviews

Review Ratings

(29% of reviews)
Show all 5 star reviews (29% of reviews)
Show all 4 star reviews (no reviews)
(14% of reviews)
Show all 2 star reviews (29% of reviews)
Show all 1 star reviews

Features

usability
Show positive (50%)Show negative (50%)(Show all)

price
Show positive (91%)Show negative (9%)(Show all)

reliability
None yetShow negative (100%)(Show all)

size
None yetShow negative (100%)(Show all)

performance
Show positive (100%)None yet(Show all)

More features

Showing 7 review(s)

Expert Reviews User Reviews

Disclaimer:

Below is a list of reviews for this or similar products. If you think this grouping is wrong please click here to flag.
Read more on our FAQ’s page.

Showing 1 - 7 of 7 Show Reviews: in English

Consumer review (newegg.com)

Not bad for the price

Price is at the lower end for the type of printing quality you get ; Print quality is pretty good compared to others at the price range ; Easy to calibrate once you know what your doing ; Loading the filament is easy and pain free even for noobs If you...

Tray needs calibrating often because of metal warping with heat constantly changing and when removing part from the tray if it's stuck to the try it take a bit of force to remove even if you don't use the glue stick. Unless you use software that uses a...

Jul, 2015

Read the full review

Consumer review (newegg.com)

Waste of your time & money

Run, don't walk. Look further cause this anchor isn't worth it.

Price alone

keeps breaking down. Arrived inoperative. Needed new display board, Heater failures are recurring. Replaced two heaters already. Broken belt already. More down time than up. Absolutely NO help from XYZ. I'm converting mine to an Arduino controller to...

Apr, 2015

Read the full review

Consumer review (newegg.com)

Great buget printer

Like all 3D printers there's no such things as plug and play even though they might try to market them as so. Be prepared to spend the time to learn about and maintain the printer. Also when buying a 3D printer do your research on what they can and can...

It's a very good price for a dual extruder printer. The print quality is pretty good out box too. I like the cartridge system as well since it keeps things nice an tidy and keeps track of how much filament is left. The software actually slices pretty...

The calibration can be a pain since the heated bed rests on top of a plastic frame. It susceptible to expansion and contraction which leads to different calibration number each time. The metal contacts used to calibrate can also get dirty fairly easily...

Feb, 2015

Read the full review

Consumer review (newegg.com)

Good quality price product

Easy, works with Autodesk product, low cost, entry level printer

Need conversion of files and adjustments, its not all automatic like a standard printer. Require some doing to print

Feb, 2015

Read the full review

Consumer review (newegg.com)

Disappointed

If I had it to do over again I would have purchased the DaVinci 1.0, saved $150 and had a great deal more mods and work arounds availabe and a larger print bed. It's probably a cheap way to get started with 3D printing but don't expect very good results.

The plug&play aspect is a nice feature and the overall package is attractive. The unit seems to be well engineered for quick factory assembly

The proprietary filament cartridge is a limitation but there are work arounds available ; The two color option seemed like a neat feature but on most of the things I have tried there is a considerable of filament mixing since the extruder apparently...

Nov, 2014

Read the full review

Consumer review (newegg.com)

Great!!!!

If i had to buy another one and would go for the single extruder model just cuz i have not found any reason to use both extruders in one print!

Works great! For the price you cannot beat HAve used high dollar ones before and dont see why you wouldnt just go with the lower priced printer cuz they produce the same product

You have to calibrate it every once in a while but once it has been done once it gets really easy

Nov, 2014

Read the full review

Consumer review (newegg.com)